#Colt agent 38 special weight how to
#Colt agent 38 special weight manual

Using the knowledge I gained from the first two guns, I decided to work on an old. The gun is perfectly reliable now and I am very happy with it. After installation the single-action trigger pull is 3.6 pounds and the double-action pull is 10.6 pounds. Numrich carries springs for virtually every Colt ever made, and I had mine inДЄbout a week. For the Detective Special, rather than try to bend the spring back, I thought it would be safer to simply order a new one. Guns like the Detective Special and Agent is going to be somewhere around 4 pounds. The optimal single-action pull, at least for D-frame So I realized that the minimum single-action trigger pulls given by Kuhnhausen are in some cases theoretical. I measured the single-action pull with my new gauge and it measured 3.2 pounds. Tried to improve the trigger and had gone a bit too far, just as Skeeter warns not to do. Secondly, I have an old Colt Detective Special with a three-inch barrel that often failed to ignite primers when fired double-action. The single actionД«reaks at 4 pounds, and the double action measures 7.8 pounds. I bought the RCBS High-Range Trigger Tension Scale, listed on as the RCBS Military Trigger Pull Scale, which is calibrated from 0 to 25 pounds.ДЇirst of all, I needed a reference, and I own an old Colt Agent with an exceptionally smooth double action that has always been reliable, so I checked it with my new trigger gauge. So before I started working on any of my Colts I ordered a trigger gauge. However, for greater precision Kuhnhausen recommends using a trigger gauge to measure the trigger pull, and gives a table of minimum and maximum trigger

#Colt agent 38 special weight manual

That is as much as Skeeter revealed about Colts, and it sounded entirely too simple, but when I consulted Jerry KuhnhausenвЂ™s Colt Shop Manual I discovered that it isД®ssentially the approved method. Other small frame guns are the Pocket Positive & Police Positive.Д® frame guns include the Army Special, Official Police, OfficerвЂ™s Models, the. Excessive working of the metal is to be avoided and it isД«etter to use a little thought and get things right the first time.Д frame guns include the Detective Special, Commando Special, Cobra, Agent, Diamondback, Police Positive Mark V, Viper, & Courier. If your bent spring has been overly weakened, it is not difficult to remove it from the gun and carefully straighten it in a vise. A ВјвЂќ rod is the largest I have ever found necessary to produce good results on large frame Colt double actions, and it would be too much for the daintier models, such as the Detective Special. Too much bending will result in a spring so weak as to cause poor ignition or misfires, and you can, of course, use a rod so thick as to break the Used until the results you want are obtained. If the bend it causes is not sufficient, gradually increase the diameter of the rod Here is a directДiameter of the rod used varies with individual springs. This bends the top arm of the spring downward over the rod and reduces the tension it places on the hammer. The next article I found was an old one by Skeeter Skelton from a 1968 issue of Shooting Times, wherein he explains that all you need to do to reduce the trigger pull on a Colt is insert a steel rodД«etween the arms of the V-shaped mainspring and cock the hammer. Leave the rest to the professionals-the problem being that there is hardly anyone left who still knows how Do not remove substantial amounts of metal-just polish the surfaces. The best you can do is to polish the surfaces of the trigger, the hammer, and the hand and rebound lever so they work smoothly againstД®ach other and against the sideplate. Hard to modify one function without affecting the other. The author further explains that most parts have at least two functions and it is Unlike automatic pistols, almost no revolver parts can be simply dropped in.вЂќ This certainly gives one pause. Virtually every internal part was hand fitted at the factory by Master assemblers with years of training andД®xperience. Point: вЂњ.the old style Colt action revolvers are complex mechanisms from another century. You may want to read it before you proceed any further.

I found an excellent article on the Colt Fever website about gunsmithing Colt revolvers. Here is what IвЂ™ve learned about the Colts.

#Colt agent 38 special weight how to

Reduced to teaching myself how to work on my own revolvers. The problem today is it is almost impossible to find a good gunsmith in the large metropolitan areas of the U.S., and if you do find one he probably has a wait time of six months to a year.